Garden Roof Assembly - Extensive
The Extensive Garden Roof® Assembly is ideally suited for locations that will receive little maintenance or where structural capabilities are a concern.
Unlike Intensive Garden Roof Assemblies, Extensive Garden Roofs are not intended for recreational use and are typically chosen for their appearance or to help reduce the "urban heat island" effect and minimize stormwater run-off. Extensive roofs only require a shallow growing media depth, generally as little as 3"-6" (depending on the region), and therefore add little weight to the roof structure below when compared to a standard ballasted PMR roof.
Recommended plant types for extensive roofs need to be drought, wind and frost resistant, such as self-generating sedums, herbs, grasses and other vegetation that can withstand harsh growing conditions.
The water stored in the growing media and drainage/retention layer is sufficient to sustain the drought resistant plants between periods of normal rainfall. Thinner assemblies and very lightweight growing media blends are available for Extensive Garden Roof Assemblies.
1.
Roofing: Material Application ( R-1 )
2.
Roofing: General Concrete Crack and Joint Treatment ( R-2 )
3.
Roofing: Concrete Construction Joints ( R-3 )
4.
Roofing: Precast Concrete Plank/Panel Joint Treatment ( R-4A )
5.
Roofing: Precast Plank Deck w/Top Slab for Standard 180 Mil Assembly ( R-4B )
6.
Roofing: Alternate Substrate Applications ( R-5A )
7.
Roofing: Alternate Substrate Applications ( R-5B )
8.
Roofing: Expansion Joint Up To 1" As-Built Widths ( R-6A )
9.
Roofing: Field Expansion Joint 1"-2" Max. As-Built Width ( R-6B )
10.
Roofing: Alternate Prefabricated Field Expansion Joints ( R-6C )
11.
Roofing: Deck-To-Wall Expansion Joint 1"-2" Max. As-Built Widths ( R-6D )
12.
Roofing: Alternate Prefabricated Deck To Wall Expansion Joints ( R-6E )
13.
Roofing: Typical Conduit Penetration & Pitch Pocket ( R-7A )
14.
Roofing: Typical Round Penetrations (Pipe, Vent, etc.) ( R-7B )
15.
Roofing: Typical Round Penetration eith HydroSeal (Pipe, Vent, etc.) ( R-7C )
16.
Roofing: Typical Drain Details ( R-8A )
17.
Roofing: Typical Drain Details ( R-8B )
18.
Roofing: Typical Curb Details ( R-9 )
19.
Roofing: Round Shape Penetration with Base Plate ( R-10A )
20.
Roofing: Typical Parapet - Covered Flashing Conditions ( R-11A )
21.
Roofing: Typical Parapet - Exposed Flashing Conditions ( R-11B )
22.
Roofing: Typical Parapet - Gypsum Board/Metal Deck Substrate ( R-11C )
23.
Roofing: Typical Parapet - At Precast Wall ( R-11D )
24.
Roofing: Typical Parapet - At Precast Wall ( R-11E )
25.
Roofing: Alternate Flashing Corner Transitions ( R-12 )
26.
Roofing: Alternate Flashing Terminations ( R-13 )
27.
Roofing: Roof Edge Termination - Typical Gravel/Paver Stop ( R-14 )
28.
Roofing: Thru-Wall Scupper Flashing ( R-15A )
29.
Roofing: Overflow Scupper Flashing ( R-15B )
30.
Roofing: Inside Corner Reinforcement ( R-16A )
31.
Roofing: Outside Corner Reinforcement ( R-16B )
32.
Roofing: Typical Tie-In Details (Curbed) ( R-17A )
33.
Roofing: Typical Tie-In Details (Horizontal) ( R-17B )
34.
Roofing: Typical Tie-In Details (Thru-Wall/Air Barrierl) ( R-17C )
35.
Roofing: Irregular Shape Penetration with Base Plate ( R-10B )
36.
Roofing: Irregular Shape Penetration Cast into Deck ( R-10C )
37.
Roofing: Complex Clustered Irregular Shaped Penetrations ( R-10D )
38.
Roofing: Pre-Flashing with Hydroseal Resin Liquid Flashing ( R-10E )
39.
Revit Object: 5. Garden Roof Assemblies – Blue Roof, Extensive, Intensive, Lawn, and Sloped Applications